Damaged 1974 Mustang 17 |
Post Reply | Page <12 |
Author | |
Joe Calcagno
Newbie Joined: November-11-2007 Location: United States Status: Offline Points: 38 |
Post Options
Thanks(0)
|
I found a strut called a 6A6.
It says it's for Correct Craft Mustangs and other older boats. Could that be the same as the 6A? Joe |
|
Joe Calcagno
Newbie Joined: November-11-2007 Location: United States Status: Offline Points: 38 |
Post Options
Thanks(0)
|
Thank you for your reply.
It's too far damaged to straighten. Do you know of a place where I can buy a new one? Thanks, Joe |
|
8122pbrainard
Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41040 |
Post Options
Thanks(0)
|
Joe,
The 6A is the strut. How bad is it since they can be straightened? |
|
Joe Calcagno
Newbie Joined: November-11-2007 Location: United States Status: Offline Points: 38 |
Post Options
Thanks(0)
|
Thank you for your rapid reply. We have had this boat since new, and it has been maintained in almost perfect condition mechanically. It ran perfectly.
Can you tell me what's a 6A? I know that it has a one inch diameter by 40 inch long shaft. I will also need a new strut. I'm trying to get photos of the bent strut so we can see what we are looking for. Thank you for your help. Sincerely, Joe Calcagno |
|
Joe Calcagno
Newbie Joined: November-11-2007 Location: United States Status: Offline Points: 38 |
Post Options
Thanks(0)
|
I made a mistake on the year model of my Mustang 17. I said it was a 1974. That was incorrect, it is a 1979 model. Sorry for any confusion. Joe |
|
Joe Calcagno
Newbie Joined: November-11-2007 Location: United States Status: Offline Points: 38 |
Post Options
Thanks(0)
|
Thank you for your gracious and rapid reply.
My shaft is one inch in diameter and exactly forty inches long overall. It has a keyway on the forward end that measures 2-1/2" long and fits a 1/4" straight key. It has a taper on the propeller end, but I don't know how to describe that taper other than it also has a 2-1/2" long by 1/4" straight keyway. The propeller end has a 3/4 x 10 right hand thread to secure the propeller. I'm trying to get photos of the strut so we can see what it looks like. Thank you again for your help. Sincerely, Joe Calcagno |
|
TRBenj
Grand Poobah Joined: June-29-2005 Location: NWCT Status: Offline Points: 21125 |
Post Options
Thanks(0)
|
M17 used a 6a. Barracuda didn’t- something with a larger flange.
M17 used a 40” shaft like the m16/skier/etc, I believe. Barracuda shaft was longer (41”) I thought. |
|
93/70 ccpb
Senior Member Joined: March-05-2006 Location: United States Status: Offline Points: 448 |
Post Options
Thanks(0)
|
measure your shaft,i have two from a barracuda about 40 inches ..and strut also dont know if strut is the same ???
|
|
what you dont want to hear from jbear and bill.you cant get in the boat till you get your minute,and they throw you back in water!
|
|
Joe Calcagno
Newbie Joined: November-11-2007 Location: United States Status: Offline Points: 38 |
Post Options
Thanks(0)
|
Dear Forum,
On Saturday morning a storm at Lake Tahoe damaged my 1974 Mustang 17. I will need a new strut and shaft. Can anyone suggest a reliable vendor for me? Joe |
|
Post Reply | Page <12 |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |