GT-40 Heads |
Post Reply ![]() |
Author | |
bchesley ![]() Senior Member ![]() ![]() Joined: October-29-2004 Location: United States Status: Offline Points: 188 |
![]() ![]() ![]() ![]() ![]() Posted: November-29-2007 at 2:59am |
I have a set of PCM GT-40 heads that i bought from JRVic on planet nautique about three months ago. He had a full valve job done on them and put I think about 200 hours on them. I was going to put them on my 2001 over the winter but I sold the boat and upgraded to a Super Sport. It already has a GT motor so I do not need them. This is a nice power upgrade and a easy bolt on. Great winter project....
I would like to get $500 OBO. Brad |
|
2001 SAN
"Python Powered" |
|
![]() |
|
mjess ![]() Newbie ![]() Joined: August-02-2007 Location: United States Status: Offline Points: 32 |
![]() ![]() ![]() ![]() ![]() |
Brad
Did you sell the GT-40 Heads? |
|
ski naut
|
|
![]() |
|
bchesley ![]() Senior Member ![]() ![]() Joined: October-29-2004 Location: United States Status: Offline Points: 188 |
![]() ![]() ![]() ![]() ![]() |
Still available.
|
|
2001 SAN
"Python Powered" |
|
![]() |
|
Bigcity ![]() Newbie ![]() Joined: November-29-2007 Location: Canada Status: Offline Points: 28 |
![]() ![]() ![]() ![]() ![]() |
Brad, I left you a message last week. I am interested in the heads. Could you provide a photo.
If everything looks good I would go $400. Thanks, Bigcity |
|
![]() |
|
bchesley ![]() Senior Member ![]() ![]() Joined: October-29-2004 Location: United States Status: Offline Points: 188 |
![]() ![]() ![]() ![]() ![]() |
I will get some pictures posted by tomorrow evening. I left my camera at work.
Brad |
|
2001 SAN
"Python Powered" |
|
![]() |
|
Bigcity ![]() Newbie ![]() Joined: November-29-2007 Location: Canada Status: Offline Points: 28 |
![]() ![]() ![]() ![]() ![]() |
Brad,my motor is a 1994 351w carbed I believe 260hp with approximately 245 hrs. My understanding is that the heads are a staright forward bolt on upgrade that would work with the stock intake and carb set up and boost hp to 290.
I am looking for a little more jam and top end. Thanks for the help. |
|
![]() |
|
TRBenj ![]() Grand Poobah ![]() ![]() Joined: June-29-2005 Location: NWCT Status: Offline Points: 21141 |
![]() ![]() ![]() ![]() ![]() |
Yup, the GT40 heads will do just that. Also consider adding an Edelbrock Performer intake manifold (new for $170, used for ~$100) at the same time. Another easy 10hp since you have it apart and putting on new gaskets anyways. |
|
![]() |
|
bchesley ![]() Senior Member ![]() ![]() Joined: October-29-2004 Location: United States Status: Offline Points: 188 |
![]() ![]() ![]() ![]() ![]() |
well crap I knew I forgot to do something. I got busy last night with the kids and totally forgot. I promise I will do it tonight. I called my wife to remind me. I knew she would come in hand one day......
|
|
2001 SAN
"Python Powered" |
|
![]() |
|
bchesley ![]() Senior Member ![]() ![]() Joined: October-29-2004 Location: United States Status: Offline Points: 188 |
![]() ![]() ![]() ![]() ![]() |
Here are some pictures. You should be able to make out the GT in the casting.
|
|
2001 SAN
"Python Powered" |
|
![]() |
|
79nautique ![]() Grand Poobah ![]() ![]() Joined: January-27-2004 Location: United States Status: Offline Points: 7872 |
![]() ![]() ![]() ![]() ![]() |
well the most import part is what you didn't show and that is the three bars on the end, yours look to only have two.
|
|
![]() |
|
TRBenj ![]() Grand Poobah ![]() ![]() Joined: June-29-2005 Location: NWCT Status: Offline Points: 21141 |
![]() ![]() ![]() ![]() ![]() |
I see 3. The GT is also indicative of the GT40 heads. Coming from JR_VIC, these heads are legit. |
|
![]() |
|
bchesley ![]() Senior Member ![]() ![]() Joined: October-29-2004 Location: United States Status: Offline Points: 188 |
![]() ![]() ![]() ![]() ![]() |
they have three. I thought the GT stamp was more important......
|
|
2001 SAN
"Python Powered" |
|
![]() |
|
Bigcity ![]() Newbie ![]() Joined: November-29-2007 Location: Canada Status: Offline Points: 28 |
![]() ![]() ![]() ![]() ![]() |
Brad, thanks for getting the photo's together.
After all that and having done a little more research I am going to go with the GT40P's from Tristatecylinder for $598 a pair. I am going to also take your advice and get the Edelbrock performer intake #2181. Looking forward to feeling the improvement. Thanks again, Bigcity |
|
![]() |
|
bchesley ![]() Senior Member ![]() ![]() Joined: October-29-2004 Location: United States Status: Offline Points: 188 |
![]() ![]() ![]() ![]() ![]() |
I have heard that the GT40P is a good head, but I was going to accecpt your offer at $400. If you want to save 198 let me know. By the way that would pay for a edelbrock intake.
Brad |
|
2001 SAN
"Python Powered" |
|
![]() |
|
Towman ![]() Groupie ![]() ![]() Joined: June-22-2006 Location: United States Status: Offline Points: 76 |
![]() ![]() ![]() ![]() ![]() |
Brad If Bigcity is not interested I am a buyer.
E mail me @ jimmmya@verizon.net what would the best payment method be and shipping $$$ to 02816 |
|
![]() |
|
bchesley ![]() Senior Member ![]() ![]() Joined: October-29-2004 Location: United States Status: Offline Points: 188 |
![]() ![]() ![]() ![]() ![]() |
Let me get a shipping quote and I will email you. Probably gonna be monday afternoon.
Brad |
|
2001 SAN
"Python Powered" |
|
![]() |
|
Towman ![]() Groupie ![]() ![]() Joined: June-22-2006 Location: United States Status: Offline Points: 76 |
![]() ![]() ![]() ![]() ![]() |
Thanks Brad payment is on the way
|
|
![]() |
|
bchesley ![]() Senior Member ![]() ![]() Joined: October-29-2004 Location: United States Status: Offline Points: 188 |
![]() ![]() ![]() ![]() ![]() |
Heads have been sold. Thanks...
|
|
2001 SAN
"Python Powered" |
|
![]() |
Post Reply ![]() |
|
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |