Plastic strut bearings |
Post Reply ![]() |
Author | |
Riley ![]() Grand Poobah ![]() ![]() Joined: January-19-2004 Location: Portland, ME Status: Offline Points: 7952 |
![]() ![]() ![]() ![]() ![]() Posted: May-14-2018 at 1:03pm |
Has anyone installed these? They are difficult to drill a dimple into them for a set screw. Is it needed? Is there are better way like maybe using heat to melt a dimple?
|
|
![]() |
|
baitkiller ![]() Platinum Member ![]() ![]() Joined: October-11-2011 Location: SW Florida Status: Offline Points: 1693 |
![]() ![]() ![]() ![]() ![]() |
drill bit worked fine. Put some locktight on the grub screws because you cant tighten them much.
|
|
Jesus was a bare-footer.............
|
|
![]() |
|
8122pbrainard ![]() Grand Poobah ![]() ![]() Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41040 |
![]() ![]() ![]() ![]() ![]() |
Bruce,
Maybe you should sharpen the drill bit. ![]() |
|
![]() |
|
JoeinNY ![]() Grand Poobah ![]() ![]() Joined: October-19-2005 Location: United States Status: Offline Points: 5697 |
![]() ![]() ![]() ![]() ![]() |
negative on that solution those things flex pretty easy, putting the set screw in against them without a dimple will deform them and keep them from turning, or leave the screw with too few threads engaged to lock - a dimple is good idea. I don't remember having any problem drilling one - so I agree on the sharp bit routine |
|
![]() |
|
MrMcD ![]() Grand Poobah ![]() ![]() Joined: January-28-2014 Location: Folsom, CA Status: Offline Points: 3620 |
![]() ![]() ![]() ![]() ![]() |
I used the plastic strut bearings on mine 3 years ago. Working fine so far with very little drag on the prop shaft. You can easily spin the shaft with one finger on the prop.
When it came to the set screws I did not like the way they fit either. I played with a few options and then drilled a hole in the strut bearing at the set screw location. I ran a tap through the hole so my set screw could screw into the plastic. I used red Loctite on the threads and put the screw into place making sure to not allow it to touch the shaft. It has worked fine for three years but I did not like any of the options when it came to this job. On a do over I think I would have purchased small screws rather than the allen head original screw and cut the screw length so it would install about 75% into the plastic. Then I could have tightened till the screw head bottomed on the strut while still using Loctite on the threads. I liked the new bearings and the way they function. I was not comfortable with the set screw set up in plastic. |
|
![]() |
|
Riley ![]() Grand Poobah ![]() ![]() Joined: January-19-2004 Location: Portland, ME Status: Offline Points: 7952 |
![]() ![]() ![]() ![]() ![]() |
Well, I broke open a new set of drills and it cut right into the plastic and made a nice dimple. Last time I installed one I had new drills, but they would not cut that stuff. I did use Locktite as you can't torque down on them very much. Thanks for the tips.
|
|
![]() |
|
8122pbrainard ![]() Grand Poobah ![]() ![]() Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41040 |
![]() ![]() ![]() ![]() ![]() |
![]() |
|
![]() |
|
8122pbrainard ![]() Grand Poobah ![]() ![]() Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41040 |
![]() ![]() ![]() ![]() ![]() |
Bruce, You must have bought the bits that were in the discount bin! ![]() |
|
![]() |
|
Riley ![]() Grand Poobah ![]() ![]() Joined: January-19-2004 Location: Portland, ME Status: Offline Points: 7952 |
![]() ![]() ![]() ![]() ![]() |
No bench grinder Pete. Maybe someday. Would like to have one and a drilled press and an abor press and....We need more room 1st.
|
|
![]() |
Post Reply ![]() |
|
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |