Boats For Sale:
GT40 stops after letting go of button |
Post Reply 
|
Page <12 |
| Author | |
lewy2001 
Grand Poobah 
Joined: March-19-2008 Location: NSW Australia Status: Offline Points: 2234 |
 Post Options
 Thanks(0)
 Quote Reply
 Posted: November-19-2014 at 8:20pm |
|
Yes if 12V is not present on the activation terminal 85 the relay will not engage and the engine will not start. In a standard ignition key this happens with ignition in the on position before you turn to crank the engine on the starter.
I have a set of 4 jumpers with a male and female on ends about 4"-6" long. |
|
|
If you're going through hell, keep going
89 Ski <a href="http://www.correctcraftfan.com/diaries/details.asp?ID=5685" ta |
|
 |
|
|
baitkiller
Platinum Member 
Joined: October-11-2011 Location: SW Florida Status: Offline Points: 1693 |
Post Options
Thanks(0)
Quote Reply
Posted: November-19-2014 at 8:26pm |
|
Dont let go of the button.
All fixed. |
|
|
Jesus was a bare-footer.............
|
|
|
|
|
rrichr
Newbie 
Joined: September-11-2014 Location: Florida Status: Offline Points: 34 |
Post Options
Thanks(0)
Quote Reply
Posted: November-20-2014 at 10:28am |
|
Bait killer, yes Jesus is "The barefooter" but even with Perfect pass I need that hand to drive😉
Lewy2001, built my jumper cables last night, cleaned my flame arrester, got my multi tester all ready to go to the lake. |
|
|
|
|
rrichr
Newbie
Joined: September-11-2014 Location: Florida Status: Offline Points: 34 |
Post Options
Thanks(0)
Quote Reply
Posted: November-28-2014 at 8:41pm |
|
So education is a good thing and I have learned a lot about my boat.... All it was was the breaker in the breaker panel in the kick plate. I put the ignition boot on and cleaned up the wiring a bit near the relays. Went for 2 boat rides:)
|
|
|
|
|
jhersey29
Senior Member 
Joined: February-20-2014 Location: Colorado Status: Offline Points: 272 |
Post Options
Thanks(0)
Quote Reply
Posted: November-28-2014 at 8:47pm |
|
Awesome!!!! Glad you found it. Did you put a new breaker in? Mine is currently at the machine shop and I am slowly working my way through rust removal on parts using Electrolysis. Fun stuff. Hope I remember how it goes back together in a few months.
|
|
|
|
|
rrichr
Newbie
Joined: September-11-2014 Location: Florida Status: Offline Points: 34 |
Post Options
Thanks(0)
Quote Reply
Posted: November-28-2014 at 8:52pm |
|
It was not even that difficult. The breakers are integrated and it just needed to be reset.
|
|
|
|
|
Bri892001
Grand Poobah
Joined: September-27-2008 Location: Boston MA Status: Offline Points: 4947 |
Post Options
Thanks(0)
Quote Reply
Posted: November-30-2014 at 1:31pm |
|
So, it was a breaker in this unit, right? I just want to get my facts straight, I'll post this fix to the GT-40 thread:
|
|
|
|
|
rrichr
Newbie
Joined: September-11-2014 Location: Florida Status: Offline Points: 34 |
Post Options
Thanks(0)
Quote Reply
Posted: November-30-2014 at 10:25pm |
|
That's correct. My boats actual circuits are different but this module, yes.
|
|
|
|
|
Bri892001
Grand Poobah
Joined: September-27-2008 Location: Boston MA Status: Offline Points: 4947 |
Post Options
Thanks(0)
Quote Reply
Posted: December-01-2014 at 12:41am |
|
Ok, cool.
|
|
|
|
|
Post Reply
|
Page <12 |
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options