Forums
NautiqueParts.comNautiqueSkins.com - Correct Craft Upholstery and Part
  New Posts New Posts RSS Feed - Engine is out what other maintenace?
  FAQ FAQ  Forum Search   Register Register  Login Login

Engine is out what other maintenace?
 Post Reply Post Reply   
Author
  Topic Search Topic Search  Topic Options Topic Options
aodmailboxes View Drop Down
Newbie
Newbie


Joined: April-23-2006
Status: Offline
Points: 3 		Post Options Post Options   Thanks (0) Thanks(0)   Quote aodmailboxes Quote  Post ReplyReply Direct Link To This Post Topic: Engine is out what other maintenace?
    Posted: April-23-2006 at 6:35pm
(Ford 351) Engine is out of my 79 Nautique. What other maintenance should I do while engine is out?? I want to get everything ready for summer.

New Hoses wires and plugs.
Exhaust hoses.
Impeller.
Motor mounts??

Bearing for drive shaft?
    -Is this difficult??
Rope for drive shaft?
    -Is this difficult??

Any maintenace suggestions would be great.

Thanks
Back to Top
M3Fan View Drop Down
Grand Poobah
Grand Poobah
Avatar

Joined: October-22-2005
Location: United States
Status: Offline
Points: 3185 		Post Options Post Options   Thanks (0) Thanks(0)   Quote M3Fan Quote  Post ReplyReply Direct Link To This Post Posted: April-23-2006 at 7:26pm
DAMPER PLATE.
Back to Top
aodmailboxes View Drop Down
Newbie
Newbie


Joined: April-23-2006
Status: Offline
Points: 3 		Post Options Post Options   Thanks (0) Thanks(0)   Quote aodmailboxes Quote  Post ReplyReply Direct Link To This Post Posted: April-24-2006 at 12:22am
http://www.skidim.com/prodinfo.asp?number=R140001

What is a damper plate?
    Anything else?
Back to Top
87sn2001 View Drop Down
Newbie
Newbie


Joined: October-27-2005
Location: Canada
Status: Offline
Points: 22 		Post Options Post Options   Thanks (0) Thanks(0)   Quote 87sn2001 Quote  Post ReplyReply Direct Link To This Post Posted: May-15-2006 at 8:19pm
the damper plat is like a flexplate on a car... it bolts between your engine and transmission..it dampins the engine torque to the transmsmion..there are springs on this plate that rust or break.. there not that expensive and easy to do when the engine is out..just sepporate the trans. from the engine and unbolt it from the engines flywheel..industrial supplie dealers sell theme cheap..there used on small bobcats..or any pcm dealer
Back to Top
Tim D View Drop Down
Grand Poobah
Grand Poobah


Joined: August-23-2004
Location: United States
Status: Offline
Points: 2635 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Tim D Quote  Post ReplyReply Direct Link To This Post Posted: May-16-2006 at 7:57am
Two things while engine is out, oil pan gasket and rear seal. If these go bad, you have to remove it again.
Tim D
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

About CCF

Since 2003, CorrectCraftFan.com has been the foremost Correct Craft reference site, and simply provides the best used Correct Craft buying and selling experience anywhere.

Donate

This site is not affiliated with Correct Craft, Inc. Funding for the site comes from members like you. Click on the link below to make a donation.

Partners

Contact

Keith@CorrectCraftFan.com
Alison@CorrectCraftFan.com
www.CorrectCraftFan.com
Copyright 2024 | Bagley Productions, LLC