Damaged 1974 Mustang 17 |
Post Reply | Page <12 |
Author | |
8122pbrainard
Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41040 |
Post Options
Thanks(0)
|
Yes, the prop end was cut 1" bringing the length down to 5" as mentioned. I pressed the cutlass in after the cut. I used a traditional 4" long brass/rubber cutlass.
|
|
Joe Calcagno
Newbie Joined: November-11-2007 Location: United States Status: Offline Points: 38 |
Post Options
Thanks(0)
|
Great advice. I'll probably do the same as soon as I get tired of looking for a 6A.
Thank you again, Joe |
|
MrMcD
Grand Poobah Joined: January-28-2014 Location: Folsom, CA Status: Offline Points: 3592 |
Post Options
Thanks(0)
|
Having the prop shaft look straight is not the same as being straight.
To check you mount the shaft in V blocks and rotate it while checking with a dial indicator to verify straight. Pete can give you exact numbers but I think it has to be within .003 of straight to avoid issues. Your eye will not see a shaft that has a .015 bend but the V blocks and a dial indiator will find it. I have a thin cut off blade for my 4" angle grinder. It makes short work cutting through things like the strut you may need to modify. I have cut thick steel with it so a brass strut should be no problem. |
|
Joe Calcagno
Newbie Joined: November-11-2007 Location: United States Status: Offline Points: 38 |
Post Options
Thanks(0)
|
Thank you, "V" blocks it is.
I'll set it up and measure the runout. Thanks again, Joe |
|
TRBenj
Grand Poobah Joined: June-29-2005 Location: NWCT Status: Offline Points: 21109 |
Post Options
Thanks(0)
|
I may have a 6a... give me a few days and I’ll try to put my hands on it.
|
|
Joe Calcagno
Newbie Joined: November-11-2007 Location: United States Status: Offline Points: 38 |
Post Options
Thanks(0)
|
That sounds interesting. I'm told that my strut is damaged beyond repair, so I will need another.
Let me know as soon as you can. Thanks, Joe |
|
8122pbrainard
Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41040 |
Post Options
Thanks(0)
|
Joe, Mark is correct with the .003". But, besides the middle of the shaft, get a reading aft of the strut. It's a common place for shafts to bend. Set the shaft in the V blocks one up around the coupling and the other were the cutlass runs. Then dial the aft end of the taper looking for the max of .003. |
|
Joe Calcagno
Newbie Joined: November-11-2007 Location: United States Status: Offline Points: 38 |
Post Options
Thanks(0)
|
Great idea, I'll do it.
Thanks, Joe |
|
zwoobah
Senior Member Joined: September-13-2018 Location: Providence RI Status: Offline Points: 308 |
Post Options
Thanks(0)
|
Joe - was browsing Bring a Trailer today and came across your name. This '62 looks beautiful. Hope you're making good progress with the boat
https://bringatrailer.com/listing/1962-chevrolet-corvette-29/ |
|
1968 Mustang 16 - 351W powered
|
|
Post Reply | Page <12 |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |