1981 SKi Nautique Restoration |
Post Reply | Page <12345> |
Author | |
MourningWood
Gold Member Joined: June-13-2014 Location: NorCal Status: Offline Points: 886 |
Post Options
Thanks(0)
|
What??
And miss out on jumping in with a safety pin to unclog the pitots? Seriously, they look brilliant! |
|
1994 Ski Nautique "Riot"
1964 Dunphy X-55 "One 'N Dun" 'I measured twice, cut three times, and it's still too short!" |
|
Wisky Badger
Senior Member Joined: July-02-2015 Location: Wisconsin Status: Offline Points: 218 |
Post Options
Thanks(0)
|
For those of you that have repainted your stripes can you please help me out with a few questions? Does the gelcoat needed to be sanded where the stripes are before before I repaint them in ordet to get proper adhesion and do I need to use primer? If I do need to sand again what grit should I be using. I am planning on using Pettit ez proxy for the paint. I have all ready wet sanded and buffed the whole boat.
I thought I saw a thread last year with one of the orange promos being restored and it looked they they where just painting over a very clean gel coat. Thanks for the help. |
|
samudj01
Gold Member Joined: March-10-2009 Location: NC Status: Offline Points: 942 |
Post Options
Thanks(0)
|
If you buffed the gel smooth then yes, sand where you are going to paint. I would tape then sand. Otherwise it will be tough to get your gel shiny right next to the paint. I’d go with 400 and see how that works in a test spot. Seems to have been enough for us but we haven’t put it to the test. You only have one color so sanding in between coats isn’t as important but the paint mfg say to lightly sand between coats. At the end, sand with 1500 or even 2000 and polish lightly. Then wax.
|
|
78 Ski Tique, 72 Skier w/302's, 93 SN w/351 & 17 GS22 w/zr409
Previous - 99 Sport Nautique w/GT40 and 87 Martinique w/351 |
|
wakemanwillis
Newbie Joined: April-02-2018 Location: Nampa Idaho Status: Offline Points: 7 |
Post Options
Thanks(0)
|
I really like the speedos! You do clean work! Putting them in the original air guide housings is a really nice touch. I am assuming they don’t compensate for say a river current? It’s just your overland speed that is measured, yes? Also is there a GPS antenna that you had to mount somewhere?
|
|
https://forum.supraboats.com/showthread.php?15768-TS6M-Stringer-Repair-pictures
|
|
TRBenj
Grand Poobah Joined: June-29-2005 Location: NWCT Status: Offline Points: 21120 |
Post Options
Thanks(0)
|
For anyone reading this that is also considering a gps speedometer conversion, be aware that Nauticlogic makes a retrofit kit that converts the original Airguides and maintains the original look 100%. A number of us have been running them for years- they are excellent.
http://www.nauticlaugic.com/airglide.html |
|
Riley
Grand Poobah Joined: January-19-2004 Location: Portland, ME Status: Offline Points: 7948 |
Post Options
Thanks(0)
|
Have their prices come down? Their kit for 2 speedos is $375 which seems very reasonable. No need for #2 to be a dummy at that price.
|
|
Wisky Badger
Senior Member Joined: July-02-2015 Location: Wisconsin Status: Offline Points: 218 |
Post Options
Thanks(0)
|
Thanks for the advice on sanding. I think I will tape all the areas that need to be sanded and then re tape before I paint to make sure I get a nice clean line.
There are not any additional GPS antenna with the Faria GPS system, everything is self contained in the Speedo. I dont think the will compensate for river current like a paddle wheel will. They probably are not as high quality as the Nauti logic kits but they are a lot cheaper. I think I picked them up on sale from Cabelas for about $70.00 each vs. $375.00 from Nauti logic. This will probably be a case of you get what you pay for but I wanted to put the cost savings toward a new prop. Tim, is the acme 540 the correct prop to run with this boat? |
|
samudj01
Gold Member Joined: March-10-2009 Location: NC Status: Offline Points: 942 |
Post Options
Thanks(0)
|
I got my best lines from some fine line tape from China. It is on amazon. I bought some more expensive tape from 3M and this outperformed it. Description below. Comes in different widths. ~1/8” did letters great. Used frisked over that. Takes a while to get here so order an extra roll!
High Temperature PVC Vinyl Fine Line Masking Tape Car Auto Paint Fineline Tape (1Roll 8mmx33m) |
|
78 Ski Tique, 72 Skier w/302's, 93 SN w/351 & 17 GS22 w/zr409
Previous - 99 Sport Nautique w/GT40 and 87 Martinique w/351 |
|
Wisky Badger
Senior Member Joined: July-02-2015 Location: Wisconsin Status: Offline Points: 218 |
Post Options
Thanks(0)
|
Timr71
Groupie Joined: March-28-2016 Location: Alabama Status: Offline Points: 80 |
Post Options
Thanks(0)
|
Wow! Looking good!
|
|
woodyelc
Senior Member Joined: February-17-2004 Location: orlando Status: Offline Points: 376 |
Post Options
Thanks(0)
|
FYI. We never sanded the side before we painted. And we used rustoleum paint.
|
|
woodyelc
|
|
Wisky Badger
Senior Member Joined: July-02-2015 Location: Wisconsin Status: Offline Points: 218 |
Post Options
Thanks(0)
|
I am guessing correct craft didn't sand before painting because it is a huge pain in the a$$ and is very labor intensive. It wasn't fun taping everything for sanding and then re taping everything for paint. If I ever do it again I will do it the original way and see how it turns out.
|
|
MourningWood
Gold Member Joined: June-13-2014 Location: NorCal Status: Offline Points: 886 |
Post Options
Thanks(0)
|
Gonna look awesome.
Did you use the graphics file in the Reference section for the "Ski Nautique"? |
|
1994 Ski Nautique "Riot"
1964 Dunphy X-55 "One 'N Dun" 'I measured twice, cut three times, and it's still too short!" |
|
8122pbrainard
Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41040 |
Post Options
Thanks(0)
|
Look'n great.
|
|
Wisky Badger
Senior Member Joined: July-02-2015 Location: Wisconsin Status: Offline Points: 218 |
Post Options
Thanks(0)
|
I didn't use the graphics from the reference section but they are a great resource. I had enough ghosting from the old paint in the gel coat that I was able to use it as a guide.
|
|
8122pbrainard
Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41040 |
Post Options
Thanks(0)
|
Dave, What was the difference in performance? |
|
samudj01
Gold Member Joined: March-10-2009 Location: NC Status: Offline Points: 942 |
Post Options
Thanks(0)
|
-pulled a crisper paint line.
-turned corners much better -didn't adhere as much making removal easier (I had to tape over cured paint when doing my black outline) |
|
78 Ski Tique, 72 Skier w/302's, 93 SN w/351 & 17 GS22 w/zr409
Previous - 99 Sport Nautique w/GT40 and 87 Martinique w/351 |
|
8122pbrainard
Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41040 |
Post Options
Thanks(0)
|
Dave,
Thanks. I'll have to get some and give it a try. Today I'll just have to do with the 3M fine line for the project. |
|
Wisky Badger
Senior Member Joined: July-02-2015 Location: Wisconsin Status: Offline Points: 218 |
Post Options
Thanks(0)
|
gt40KS
Gold Member Joined: August-05-2017 Location: Wichita Kansas Status: Offline Points: 943 |
Post Options
Thanks(0)
|
Looks great - Good job!
|
|
JCCI
1995 Ski Nautique GT40 |
|
8122pbrainard
Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41040 |
Post Options
Thanks(0)
|
Look'n great.
|
|
samudj01
Gold Member Joined: March-10-2009 Location: NC Status: Offline Points: 942 |
Post Options
Thanks(0)
|
Very nice looking! You spray or brush?
|
|
78 Ski Tique, 72 Skier w/302's, 93 SN w/351 & 17 GS22 w/zr409
Previous - 99 Sport Nautique w/GT40 and 87 Martinique w/351 |
|
fanofccfan
Platinum Member Joined: December-13-2009 Location: North Bend NE Status: Offline Points: 1726 |
Post Options
Thanks(0)
|
I had an 81 like that and bought it somewhat molested....yours looks great!
|
|
2004 196 LE Ski 1969 Marauder 19 1978 Ski
|
|
Wisky Badger
Senior Member Joined: July-02-2015 Location: Wisconsin Status: Offline Points: 218 |
Post Options
Thanks(0)
|
I used the rolling and tipping method.
|
|
MechGaT
Senior Member Joined: March-09-2015 Location: Chattanooga Status: Offline Points: 271 |
Post Options
Thanks(0)
|
Lookin’ good!
|
|
'92 Sport Nautique
|
|
Wisky Badger
Senior Member Joined: July-02-2015 Location: Wisconsin Status: Offline Points: 218 |
Post Options
Thanks(0)
|
I have a some questions on mounting the engine cradle.
1) Should I drill the pilot holes and apply CPES allowing it to cure before installing the lag bolts or do I apply the CPES and install lag bolts immediately? 2) Should I also apply 4200 to the lag bolts to help seal them? I also will be installing a new cutlass bearing in the strut. I plan on removing the strut so I can re bed the strut in 4200 and make sure my alignment is correct. Is there any reason why I would want to install the cutlass while the strut is still attached the the boat? |
|
8122pbrainard
Grand Poobah Joined: September-14-2006 Location: Three Lakes Wi. Status: Offline Points: 41040 |
Post Options
Thanks(0)
|
Jacob,
I would allow the CPES to partially cure before running the lags in but, make it all soaked into the wood and there isn't a puddle at the bottom. If there is, you'll need to redrill the pilot hole. Yes on the 4200 to completely seal the holes. Replacing the cutlass will be easier with the strut removed. |
|
Smithfamily
Platinum Member Joined: December-26-2007 Location: Orlando, Fl Status: Offline Points: 1602 |
Post Options
Thanks(0)
|
Sure is coming along nice. Enjoying the reports.
|
|
Js
|
|
Wisky Badger
Senior Member Joined: July-02-2015 Location: Wisconsin Status: Offline Points: 218 |
Post Options
Thanks(0)
|
Thanks for the help.
|
|
linden92
Newbie Joined: March-07-2017 Location: Florida Status: Offline Points: 1 |
Post Options
Thanks(0)
|
Subscribed! looks killer, I started my build about 2 years ago but it ended up on the back burner because I bought a tunnel hull for fishing tournaments and that got bumped ahead. Finally have all the glass and body work done on that build and excited to get back to the correct craft! If you ever found the prints you had drawn up for the stringers I would live to take a look at them. some of my measurements and pics have gotten lost over the years.
|
|
Post Reply | Page <12345> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |