1985
Printed From: CorrectCraftFan.com
Category: Buy and Sell
Forum Name: Boat Parts Wanted
Forum Discription: Parts wanted only
URL: http://www.CorrectCraftFan.com/forum/forum_posts.asp?TID=42464
Printed Date: June-15-2024 at 6:13pm
Topic: 1985
Posted By: Red
Subject: 1985
Date Posted: March-06-2018 at 5:12am
Ski pylon previous owner cut the ring off to install wake board pole.
|
Replies:
Posted By: NCH20SKIER
Date Posted: March-06-2018 at 9:34am
Clown
------------- '05 206 Limited '88 BFN
|
Posted By: Wil
Date Posted: March-27-2018 at 5:27pm
Posted By: 8122pbrainard
Date Posted: March-27-2018 at 5:45pm
Wil wrote:
There is one on ebay | Pylon with a ring and finger? How about a link?
------------- /diaries/details.asp?ID=1622" rel="nofollow -
54 Atom
/diaries/details.asp?ID=2179" rel="nofollow - 77 Tique
64 X55 Dunphy
Keep it original, Pete <
|
Posted By: NCH20SKIER
Date Posted: March-27-2018 at 5:55pm
I have a pylon and am less than 90 minutes from Lake Norman. Not perfect but has the ring and finger attached.
------------- '05 206 Limited '88 BFN
|
Posted By: Donald78
Date Posted: March-31-2018 at 7:03pm
I have a pylon chrome off of 86 ski nautiquie 2001
|
Posted By: LDH
Date Posted: March-31-2018 at 10:35pm
I am interested in getting this. I need it for my boat. How can I get in contact with you?
|
Posted By: LDH
Date Posted: March-31-2018 at 10:36pm
I am interested in this. I need it for my boat. How can I get in contact with you? This is for Red.
|
Posted By: Donald78
Date Posted: April-29-2018 at 3:48pm
I am sorry it to so long to get back did you a ply on thanks Donald 78 419 788 0523
|
Posted By: LDH
Date Posted: April-29-2018 at 4:28pm
I have not found one yet but I want it......
|
Posted By: repifanio2
Date Posted: June-24-2018 at 8:33pm
How do you take the ring off the pylon?
------------- RKE
|
Posted By: Wil
Date Posted: June-29-2018 at 6:50pm
should be allen set screws to remove
|
Posted By: TRBenj
Date Posted: June-29-2018 at 7:06pm
Wil wrote:
should be allen set screws to remove | No.
Roll pins.
|
Posted By: 8122pbrainard
Date Posted: June-29-2018 at 7:10pm
repifanio2 wrote:
How do you take the ring off the pylon? |
TRBenj wrote:
Wil wrote:
should be allen set screws to remove | No.
Roll pins. |
8122pbrainard wrote:
Ralph, You'll see a hole below the ring/finger where there's a spring pin. Some call them a roll pin. It's what's holding the ring/finger in the pylon and it needs to be driven out. Then the shank can be really stuck due to corrosion. Some have resorted to applying upwards force with a chain hoist or "come a long" while twisting the ring back and forth. Be carefull not to apply too much force on the ring since some have bent them.
|
Lynn, What kind of boat do you have?
------------- /diaries/details.asp?ID=1622" rel="nofollow -
54 Atom
/diaries/details.asp?ID=2179" rel="nofollow - 77 Tique
64 X55 Dunphy
Keep it original, Pete <
|
Posted By: repifanio2
Date Posted: June-30-2018 at 12:37pm
86 2001 I got one pin our but probably bent the other
------------- RKE
|
Posted By: 8122pbrainard
Date Posted: June-30-2018 at 1:01pm
Ralph,
8122pbrainard wrote:
Pin punch
| Pin punches are sized to be slightly smaller than the pin you are removing. If you use too small a punch, you can "mushroom" the pin end and locking it in the hole. Did you use the proper size? My suggestion now is to remove the pylon and get it into an arbor press to see if the pin will come out. You may have to resort to drilling it out but that can be tricky since the pin is hard. A carbide drill in a drill press would be needed.
------------- /diaries/details.asp?ID=1622" rel="nofollow -
54 Atom
/diaries/details.asp?ID=2179" rel="nofollow - 77 Tique
64 X55 Dunphy
Keep it original, Pete <
|
Posted By: repifanio2
Date Posted: June-30-2018 at 3:43pm
thanks for your help
------------- RKE
|
|