thermostat housing, impellar |
Post Reply ![]() |
Author | |
bsucics ![]() Senior Member ![]() ![]() Joined: July-18-2006 Location: United States Status: Offline Points: 109 |
![]() ![]() ![]() ![]() ![]() Posted: October-14-2006 at 11:44am |
I'm trying to remove the thermostat housing - the screws are out, but it's not going to budge. Any suggestions would be appreciated as I don't want to damage anything trying to get it off.
Also, after removing the impeller, discovered that 2 vanes had broken off. The hose between the water pump and thermostat housing was clean. Do I let this go, or should I be searching for them? Thanks |
|
![]() |
|
The Dude ![]() Platinum Member ![]() ![]() Joined: October-19-2004 Location: Houston Status: Offline Points: 1334 |
![]() ![]() ![]() ![]() ![]() |
the thermostat housing is just stuck from the gasket. Carefully bang on it. Or sometimes you can use a putty knife to get under the gasket and that will give you some leverage on it.
The rubber for the impeller is probably in there somewhere. If you don't want to rip into it, then just keep your eye on the temp gage. A common place for pieces to show up is near the tranny oil cooler. |
|
Mullet Free since 93
95 Sport |
|
![]() |
|
bsucics ![]() Senior Member ![]() ![]() Joined: July-18-2006 Location: United States Status: Offline Points: 109 |
![]() ![]() ![]() ![]() ![]() |
yup - putty knife did the trick. thanks
|
|
![]() |
|
Tim D ![]() Grand Poobah ![]() Joined: August-23-2004 Location: United States Status: Offline Points: 2637 |
![]() ![]() ![]() ![]() ![]() |
Those impellor pieces will get stuck in the exhaust manifolds and in the bypa$$ hose 90 degree fixture if you have one. They are also the perfect size to get stuck in water veins in the block. Use a little blue rtv to hold the gasket in place when you put the thermostat back in.
|
|
Tim D
|
|
![]() |
|
bsucics ![]() Senior Member ![]() ![]() Joined: July-18-2006 Location: United States Status: Offline Points: 109 |
![]() ![]() ![]() ![]() ![]() |
Thanks for the suggestion, I wasn't familiar with that, but I'll give it a try. The old gasket is a mess - any tips on cleaning the housing to prep for the new gasket?
|
|
![]() |
|
Tim D ![]() Grand Poobah ![]() Joined: August-23-2004 Location: United States Status: Offline Points: 2637 |
![]() ![]() ![]() ![]() ![]() |
Get one of those gla$$ scrapers that holds a razor blade.
|
|
Tim D
|
|
![]() |
|
TRBenj ![]() Grand Poobah ![]() ![]() Joined: June-29-2005 Location: NWCT Status: Offline Points: 21141 |
![]() ![]() ![]() ![]() ![]() |
Gasket remover makes the work easier too. Comes in a spray can, available at auto parts stores.
|
|
![]() |
|
Tim D ![]() Grand Poobah ![]() Joined: August-23-2004 Location: United States Status: Offline Points: 2637 |
![]() ![]() ![]() ![]() ![]() |
Yeah, that stuff works great on head gaskets, but never had to use it on a thermo gasket.
|
|
Tim D
|
|
![]() |
|
87BFN owner ![]() Grand Poobah ![]() ![]() Joined: August-25-2006 Location: Ypsilanti, MI Status: Offline Points: 2194 |
![]() ![]() ![]() ![]() ![]() |
I use a wirebrush that goes in a drill motor, removes left over stuck on gasket but no metal from thermo housing or intake.
|
|
![]() |
|
Rick ![]() Senior Member ![]() Joined: March-03-2004 Location: United States Status: Offline Points: 338 |
![]() ![]() ![]() ![]() ![]() |
I usually use a gasket scraper. You really want to find those pieces. I would check the Tranny cooler and the hoses to the manifolds. It is possible that they will block a cooling loop and all of a sudden the manifold or block will get really hot. It could do some damage.
|
|
![]() |
Post Reply ![]() |
|
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |