67 Mustang gas gauge (mechanical) |
Post Reply ![]() |
Author | |
Atmspltr ![]() Senior Member ![]() Joined: May-04-2005 Location: United States Status: Offline Points: 170 |
![]() ![]() ![]() ![]() ![]() Posted: May-03-2006 at 9:11pm |
ORIGINAL gas gauge from a 67 Mustang. NOT a sending unit. This is one that you had to look down through the rear deck to see check the level. Works and looks great.
|
|
![]() |
|
fredo68 ![]() Senior Member ![]() Joined: April-03-2006 Location: United States Status: Offline Points: 138 |
![]() ![]() ![]() ![]() ![]() |
how much? how is the lettering
on the guage? is the glass broke? fredo68 |
|
fredo68
|
|
![]() |
|
Atmspltr ![]() Senior Member ![]() Joined: May-04-2005 Location: United States Status: Offline Points: 170 |
![]() ![]() ![]() ![]() ![]() |
Gauge glass is intact and good.
Lettering is good. Send your email and I'll send a picture. $30 sound reasonable? |
|
![]() |
|
fredo68 ![]() Senior Member ![]() Joined: April-03-2006 Location: United States Status: Offline Points: 138 |
![]() ![]() ![]() ![]() ![]() |
sounds fair to me, do you have any
other parts. fredo68 |
|
fredo68
|
|
![]() |
|
fredo68 ![]() Senior Member ![]() Joined: April-03-2006 Location: United States Status: Offline Points: 138 |
![]() ![]() ![]() ![]() ![]() |
emaik for fredo68 is
southcentralmotors@verizon.net |
|
fredo68
|
|
![]() |
|
Atmspltr ![]() Senior Member ![]() Joined: May-04-2005 Location: United States Status: Offline Points: 170 |
![]() ![]() ![]() ![]() ![]() |
Chrysler 318 exhaust manifolds/risers...aluminum bellhousing (318)...one lift ring (good shape, minor wear)...original brass prop shaft with hub...propeller...I could get the original 318 engine, motor mounts, etc if needed...I think that's it.
RB |
|
![]() |
|
fredo68 ![]() Senior Member ![]() Joined: April-03-2006 Location: United States Status: Offline Points: 138 |
![]() ![]() ![]() ![]() ![]() |
i had to use the shaft out of my 66
for my 68 due to some stroke welding the shaft to the hub and not using the key. how much would you take for the gas gauge,shaft,prop,and hub. that did come off of a velvet drive right. im in northern indiana, how much to ship you think. if you want call me at 2607406611. very nice looking 67 by the way fredo68 |
|
fredo68
|
|
![]() |
|
Atmspltr ![]() Senior Member ![]() Joined: May-04-2005 Location: United States Status: Offline Points: 170 |
![]() ![]() ![]() ![]() ![]() |
Fred,
How about $125 for the lot? I'll figure out shipping and email you with a total if you are agreeable. I don't recall if it was a velvet drive...I would think no more than $10-$15 for shipping...FYI, there have been posts regarding a recommendation from Correct Craft to replace the prop shaft on regular basis. This was the original shaft and has had considerable run time. I'd feel comfortable using it as a spare but it may be safer to go to a machine shop and have one made out of stainless. Thanks for checking out the '67...it's been alot of work. |
|
![]() |
|
Atmspltr ![]() Senior Member ![]() Joined: May-04-2005 Location: United States Status: Offline Points: 170 |
![]() ![]() ![]() ![]() ![]() |
Sorry fredo...I mis-spoke. I do not have the prop. It went to my dad (76 Ski Tique). I'll sell the fuel gauge, prop shaft and hub for $50. I'll try to send pictures today.
RB |
|
![]() |
|
fredo68 ![]() Senior Member ![]() Joined: April-03-2006 Location: United States Status: Offline Points: 138 |
![]() ![]() ![]() ![]() ![]() |
if you havent received my reply
to your email that sounds great just making sure its al brooke 2127 s calhoun ft wayne in 46802 thanks again fredo68 |
|
fredo68
|
|
![]() |
|
Atmspltr ![]() Senior Member ![]() Joined: May-04-2005 Location: United States Status: Offline Points: 170 |
![]() ![]() ![]() ![]() ![]() |
Got it Fredo...I'll mail it in the next few days.
RB |
|
![]() |
|
fredo68 ![]() Senior Member ![]() Joined: April-03-2006 Location: United States Status: Offline Points: 138 |
![]() ![]() ![]() ![]() ![]() |
thank you sir, whats up with the
68 ss in florida wish it was closer where are you at? fredo68 |
|
fredo68
|
|
![]() |
|
Atmspltr ![]() Senior Member ![]() Joined: May-04-2005 Location: United States Status: Offline Points: 170 |
![]() ![]() ![]() ![]() ![]() |
I'm in Smithfield Virginia. I live on brackish water and won't put my boat in it..boat play usually occurs on Lake Gaston, NC. Looking forward to getting back out there! I'm still negligent in geting your stuff shipped but I'll get it...I promise.
|
|
![]() |
|
PKster ![]() Newbie ![]() Joined: January-11-2004 Location: United States Status: Offline Points: 28 |
![]() ![]() ![]() ![]() ![]() |
Still have the gas gauge for sale?
|
|
![]() |
|
Atmspltr ![]() Senior Member ![]() Joined: May-04-2005 Location: United States Status: Offline Points: 170 |
![]() ![]() ![]() ![]() ![]() |
Sorry, no. It's to be shipped out this week to fredo.
RB |
|
![]() |
|
fredo68 ![]() Senior Member ![]() Joined: April-03-2006 Location: United States Status: Offline Points: 138 |
![]() ![]() ![]() ![]() ![]() |
atmspltr
no rush at your convenience, that ss is in st pete, fla would be great parts boat for both of us. i have 2 mustangs that need little things. im sure you need some parts, like the platform. the guy wants to sell whole boat no parts. and thanks again the shaft will allow another classic back in the water. fredo68 |
|
fredo68
|
|
![]() |
Post Reply ![]() |
|
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |